Metal Roofing in Cypress built to outlast shingle
Metal Roofing in Cypress is a standing seam or corrugated panel system that sheds rain, resists wind uplift, and holds its color for decades instead of years. We install it for homeowners in Cypress, Los Alamitos, and Buena Park who are tired of replacing asphalt shingles every 15 to 20 years. If you want a Cypress CA metal roofer who measures your roof, not a sales script, we can help.
Service overview
Metal Roofing in Cypress, done panel by panel
Metal Roofing in Cypress is a roof system that uses interlocking steel or aluminum panels instead of shingles, fastened over a synthetic underlayment and ice and water shield along the valleys and eaves. Panels run from ridge to eave in single lengths, so there are fewer seams for water to find. We install standing seam, corrugated, and exposed-fastener profiles, and we cut each panel on site with tin snips and a power drill so it fits your actual roof, not a factory average. Cypress sits in a pocket where summer attic temperatures push past 140 degrees and marine fog rolls in most mornings from March through August. That cycle punishes asphalt shingles. Metal roofing Cypress California homeowners choose reflects a good share of that heat, and the panels do not crack when the temperature swings. If you have been searching metal roofing in Cypress CA near me because your third shingle patch in four years failed, the problem is usually the material, not the installer.
! Problems we solve
Shingles cracking and curling after 12 to 15 years
Cracked shingles let water into the deck, which leads to roof rot, stained ceilings, and eventually a full tear-off under emergency conditions instead of on your schedule.
Attic heat pushing 140 degrees in summer
A hot attic radiates down into the living space, so the air conditioner runs longer, second-floor rooms stay uncomfortable, and your energy bill climbs every July and August.
Wind damage lifting shingles and flashing
Once shingles lift, the next rain gets under them and water finds the deck. Repeated wind damage also means repeated insurance claims, which can eventually affect your coverage.
Scope of work
What a metal roof installation includes
Every metal roof we install in Cypress includes tear-off, deck inspection, underlayment, panels, flashing, and cleanup. What changes from job to job is the panel profile, the color, and how much deck repair the old roof left behind. We list all of it in the written scope so you know what you are paying for.
-
01
Tear-off and disposal
We remove the existing shingles, tile, or old metal and haul it away the same day. The deck gets inspected board by board. Soft or delaminated sheathing is replaced before anything new goes down, because a metal roof is only as good as what it is fastened to.
-
02
Underlayment and ice and water shield
Synthetic roof underlayment goes over the full deck, with ice and water shield at the eaves, valleys, and around penetrations. In Cypress, the valleys take the heaviest water during winter storms, so that is where the extra membrane matters most.
-
03
Panels, clips, and fasteners
Standing seam panels are set with concealed clips and mechanically seamed. Corrugated panels use exposed fasteners with neoprene washers. Either way, we follow the manufacturer's fastening pattern and spacing so the finish warranty stays valid.
-
04
Flashing, trim, and ventilation
Drip edge, ridge vent, pipe boots, and custom flashing at chimneys and skylights are all part of the install. We balance soffit intake with ridge exhaust so the attic breathes. Roofing caulk is used only where the system requires it, never as a cover-up.
Why Cypress homeowners switch to metal
Metal roofing changes the math on roof ownership. You pay more on day one and then stop paying for patches, granules in the gutter, and attic heat that never quite goes away.
Book an estimateTools and methods we use
Roofing nail gun
Drives underlayment and deck fasteners at consistent depth so nothing over-drives into the sheathing. We adjust pressure per deck thickness before the first panel goes down.
Pitch hoist
Lifts metal panels and shingle bundles up the roof slope without dragging them across the finish. Keeps the panel edges straight and the crew off ladders with heavy loads.
Tin snips and power drill
Cuts and fastens panels on site so each piece fits your actual roof. We cut with snips rather than a grinder, because heat from a grinder can burn the finish and void the warranty.
Chalk line and caulking gun
Snaps the reference line for the first panel course so every panel runs true to the ridge. The caulking gun applies sealant only at the joints and penetrations the system calls for.
Local execution
Cypress sits in northwest Orange County, close enough to the coast to get marine fog most mornings from late spring through summer, and far enough inland to hit triple digits in August and September. That combination is hard on asphalt shingles and easy on metal. The fog keeps the deck damp, which accelerates rot under a failed shingle field, while the summer heat bakes the attic. A metal roof with proper underlayment and balanced ventilation handles both. We also work with Cypress building code, which follows California Title 24 energy requirements and the state's wildfire-zone material rules in the hillside edges of the county. If you are pricing metal roof installation Cypress California cost, the biggest variables are square footage, panel profile, and how much deck repair the old roof left behind. We measure and give you a written range, not a phone estimate.
How metal roofing works in Cypress
- • Cypress College area
- • Lincoln Avenue corridor
- • Los Alamitos border
- • Valley View and Orangewood
Recent work
Metal roofing help when Cypress weather turns
We answer when your roof leaks
When a storm opens a seam or a branch punches through a panel, you do not want a voicemail. Pro Roofing Cypress answers emergency calls 24/7 and can usually have a crew at your Cypress home within two to four hours for active leaks. Our trucks carry tarps, roofing caulk, flashing material, and temporary patch supplies, so we can stop the water the same visit and schedule the permanent metal repair. For non-emergency estimates, call before noon and we can typically get an estimator to your home within 24 to 48 hours. We are based locally in the 90630 ZIP, which means we are not driving in from two counties away while your ceiling drips. If you need a Cypress metal roof company that picks up the phone, call us.
How a metal roof goes on
Inspection and measurement
We walk the roof, check the deck, look at flashing failure around chimneys and skylights, and measure every plane and valley. You get a written scope with panel profile, color, and gauge. This visit takes about 90 minutes on a typical Cypress ranch home.
Tear-off and deck prep
The old shingles come off with a shingle ripper and pitch hoist, and we haul them out the same day. We replace any soft decking, then roll synthetic underlayment and ice and water shield at the eaves and valleys. Most tear-offs run one to two days.
Panel layout and cutting
We snap a chalk line for the first panel so every course runs true, then cut panels on site with tin snips and a power drill. Panels are lifted with a pitch hoist and set with clips or exposed fasteners, depending on the profile you chose. This is the longest phase, usually two days.
What metal roofing costs in Cypress
Metal roofing costs more up front than asphalt shingles, and it lasts two to three times as long. For a typical Cypress home in 2026, most full metal roof installations land between $14,000 and $32,000. The range is wide because square footage, panel profile, roof complexity, and deck condition all move the number. We give you a written, itemized range after we measure, so you can compare it against a shingle quote with the same scope.
Roof size and pitch
Square footage is the biggest driver. A steep pitch slows the crew down and requires more safety setup, which adds labor. A simple gable roof on a 1,700-square-foot home costs far less than a cut-up two-story with multiple valleys and dormers.
Panel profile and gauge
Standing seam panels cost more than exposed-fastener corrugated because of the concealed clip system and the seaming labor. Heavier gauge steel costs more than lighter gauge. We quote both profiles so you can see the difference and choose.
Deck condition and tear-off layers
Multiple shingle layers mean more tear-off labor and disposal fees. Soft or delaminated sheathing has to be replaced before the panels go on. We inspect after tear-off and show you the photo and per-sheet price before we replace anything.
Licensed, certified, and reviewed
Metal roofing questions we hear
How much does metal roofing cost in Cypress CA?
Most Cypress homes land between $14,000 and $32,000 for a full metal roof in 2026, depending on square footage, panel profile, and how much deck repair is needed. Standing seam runs higher than corrugated. A typical 1,800-square-foot ranch home with a simple gable and no deck damage usually comes in near the lower end. We give you a written range after measuring, not a phone guess.
Who installs metal roofs in Cypress California?
Pro Roofing Cypress installs standing seam and corrugated metal roofs across Cypress and Orange County. We hold California Contractor License C-39 and have been in business since 2000. Our crews handle tear-off, deck repair, underlayment, flashing, and ventilation in-house. If you want a Cypress metal roof company that will still be around for the warranty call, we are at 90630 and the surrounding cities.
How long does a metal roof last in Cypress CA?
A properly installed metal roof in Cypress lasts 40 to 70 years, against 15 to 20 for asphalt shingles. The panels themselves often outlive the finish, which is why the factory paint warranty matters. Coastal fog and summer heat are the two things that age a roof here, and metal handles both better than shingle. We install to manufacturer spec so the finish warranty stays valid.
Do you offer metal roofing near me in Cypress?
Yes. We serve all of Cypress, including the 90630 ZIP, plus Los Alamitos, La Palma, Buena Park, Cerritos, and the surrounding Orange County cities. Call before noon and we can usually schedule an estimate within 24 to 48 hours. For leaks or storm damage, we offer 24/7 emergency response and same-day tarping to stop water until the permanent repair is scheduled.
Related services
Roof Installation
A metal roof is a full roof installation, not a cover-up. We strip the old shingles, inspect and repair the deck, then install underlayment and panels. If you are building new in Cypress, we can spec the metal system from the framing stage.
Roof Replacement
Most metal roof jobs are replacements. We tear off the existing shingle or tile, haul it away, and install the metal system in one continuous project. Typical Cypress replacements run two to four days on the roof, weather permitting.
Get your Metal Roofing in Cypress estimate
We measure your roof, check the deck, and give you a written range with panel options and colors. No pressure, no same-day signing discount. Call Pro Roofing Cypress and we will schedule a visit within 24 to 48 hours.